DC8065
Electric Water Pump - Xtreme Outback Heavy Duty Clutch for 4x4 Vehicles
EWP150 Black Kit - Remote Electric Water Pump (12V)
Xtreme Outback Clutch Technical Specifications & Features
- Operating voltage
- 3V DC to 15V DC
- Maximum current
- 10A @ 13V
- Flow rate (max)
- 162L/min (42.8 US gal/min) @ 13V DC
- Operating temp.
- -40° to 120°C (-40° to 248°F)
- Pump design
- Clockwise centrifugal with volute chamber
- Pump material
- Aluminium (Powder Coated)
- Burst pressure
- 500 kPa (72.5 psi)
- Seal
- Ceramic face seal
- Self Priming
- No, none of pumps are self-priming
- Fits hose size
- 35mm to 51mm (1.38” to 2”)
- Push-On fitting Size
- EWP Inlet & Outlet 38mm (with 3mm Sleeve (#8510) 44mm) (with 6mm Sleeve (#8511) 51mm)
- Internal Fitting
- -Inlet & Outlet: -16AN ORB
- Weight
- 1.4 kg
Buy Heavy Duty Clutch - Pricing & Availability Information
Heavy Duty Clutch Product Overview & Performance Details
Celebrating 50 years, Davies Craig Pty Ltd has launched a ‘BLACK LABEL’ EWP®150 Remote-Mounted Electric Water Pump! Supplied in glorious matt black powder-coat, it offers modern performance, compactness, and style.
Muscle up your engine cooling system with the EWP®150. Like all EWPs, this advanced unit is designed for remote mounting in the engine bay to satisfy those higher horsepower, turbocharged, supercharged and ‘worked’ engines which develop excessive heat & intercooler applications. This rugged alloy hi-flow pump increases power and improves coolant temperature control.
| Option | Part DC | Notes |
|---|---|---|
| Pump Only | DC8165 | EWP®150 Black Alloy 12V pump only. |
| Kit | DC8065 | EWP®150 Black Alloy 12V kit with basic wiring essentials (see contents below). |
| Combo with Controller | DC8975 | Combo pack with controller solution (controller also available separately). |
| Item | Qty |
|---|---|
| EWP®150 Black Alloy (12V) | 1 |
| EWP Basic Wiring Harness (with 10amp Fuse) | 1 |
| Hose Clamps | 2 |
| RED – Wire Joiner | 1 |
| RED – 6mm Ring Terminal | 1 |
| RELAY – 12V 40 Amp 5 Pin w/ Resistor Protection | 1 |
| SCREW – SELF TAP 8X3/8 BZ | 1 |
| Operating voltage | 3V DC to 15V DC |
| Maximum current | 10A @ 13V |
| Flow rate (max) | 162 L/min (42.8 US gal/min) @ 13V DC |
| Operating temp. | -40° to 120°C (-40° to 248°F) |
| Pump design | Clockwise centrifugal with volute chamber |
| Pump weight | 1,170 grams (2.6 lb) |
| Pump material | Aluminium (Powder Coated) |
| Internal Fittings | Inlet & Outlet: -16AN ORB |
| Fits hose sizes | 35mm to 51mm (1.38” to 2”) |
| Push-on fitting size | EWP inlet & outlet 38mm
|
EWP & Controller Installation Demonstration
Combined with an LCD EWP®/Fan Digital Controller (Sold separately Part DC8002 or combo DC8975) will manage both the EWP® and Thermatic® fan operation. The Digital Controller will vary the speed of the EWP® in response to the engine’s coolant temperature, eliminating ‘heat soak’ and extending engine life.
The world’s most advanced total engine cooling management system:
universal fit
more power
more cooling
increase fuel efficiency
extend engine life
world-leading technology
Installing an EWP® as an AUXILIARY PUMP
- Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose.
- Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.
EWP® INSTALLATION – disabling Mechanical water pump
- Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose and remove the manufacturer’s thermostat.
- You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
- If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.
In both these cases, the EWP® will pump past the impeller of the mechanical water pump.
Disengaged mechanical water pump (recommended)
- Remove the mechanical water pump and remove the thermostat.
- Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.
- Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
- Install the EWP® into the bottom radiator hose.
Removed mechanical water pump (Ideal)
- Remove the mechanical water pump and thermostat from the engine.
- Install a Davies Craig EWP® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
- Install the EWP® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
- Install an appropriate length belt (not supplied) to drive the accessories.
In most cases EWP® will be adequately supported by the radiator hose. Where mounting is required, the EWP® must be soft mounted to protect against vibration. For the EWP®115, EWP®140 and EWP®150 Part DC8700 or DC8710 Mounting bracket is recommended.
PRODUCT SELECTION GUIDE
| EWP® PRODUCT SELECTION GUIDE | |||||||
| APPLICATION | PUMP MODEL |
PUMP ONLY | PUMP KIT | PUMP COMBO | |||
| 12V | 24V | 12V | 24V | 12V | 24V | ||
| Engines up to 2.0L (Standard) |
EWP®80 | DC8106 Flange DC8109 Barb |
N/A | DC8006 Flange DC8009 Barb |
N/A | DC8908 Flange DC8919 Barb |
N/A |
| Engines up to 2.0L - 3.5L (Standard) |
EWP®115 | DC8125 Nylon DC8140 Alloy |
DC8126 Nylon DC8141 Alloy |
DC8025 Nylon DC8040 Alloy |
N/A | DC8930 Nylon DC8950 Alloy |
N/A |
| Engines up to 3.5L - 5.0L (Standard) |
EWP®140 | DC8180 Alloy | DC8181 Alloy | DC8080 Alloy | N/A | DC8990 Alloy | N/A |
| Engines 5.0L or greater (Standard) Modified Engines Supercharged/Turbo, Drag Racing, 4WD, Off Road, Drifting & Speedway |
EWP®150 | DC8160 Silver DC8165 Black |
DC8161 Silver | DC8060 Silver DC8065 Black |
DC8061 Silver | DC8970 Silver DC8975 Black |
DC8971 Silver |
| Intercooler (depending on capacity) |
EWP®115 | DC8125 Nylon DC8140 Alloy |
DC8126 Nylon DC8141 Alloy |
DC8025 Nylon DC8040 Alloy |
N/A | DC8930 Nylon DC8950 Alloy |
N/A |
| EWP®140 | DC8180 Alloy | DC8181 Alloy | DC8080 Alloy | N/A | DC8990 Alloy | N/A | |
| EWP®150 | DC8160 Silver DC8165 Black |
DC8161 Silver | DC8060 Silver DC8065 Black |
DC8061 Silver | DC8970 Silver DC8975 Black |
DC8971 Silver | |
| EWP®160 | N/A | N/A | DC8430 | N/A | N/A | N/A | |
| EWP®180 | N/A | N/A | DC8450 | DC8451 | N/A | N/A | |
Related Heavy Duty Clutch Products & Accessories
No related products available.
Compatible 4x4 Vehicle Applications & Fitment Guide
No vehicle applications specified for this product.
No variants available for this product